![]() ![]() help-gstout Show GStreamer Output Options. Help options ¶ -h, -help Show summary of options. To log to the terminal use use -logfile devstdout This fileĬan get quite large over time, so it is only recommended to use this logfile Name of a file to log output of the program to. dump-transport-scpd Dump A/V Transport service description XML and exit. dump-control-scpd Dump Rendering Control service description XML and exit. dump-connmgr-scpd Dump Connection Manager service description XML and exit. Debug options: ¶ -dump-devicedesc Dump device descriptor XML and exit. Use -output to obtain a list of valid modules. list-outputs List available output modules and exit. Volume level, but only internal attenuation. Note that this does not influence the hardware (e.g. The decibel scale is non-linear: -20db represents roughly half volume. Values range from 0 (maximum volume) to -60 (minimum volume. gstout-initial-volume-db Sets the initial volume on startup in decibels. TheĬorrect values will depend on which method of audio output (e.g. options allow the user toĬonfigure where the sound output from gmediarender is sent. I want to use Gmediarenderer with my new Logitech USB DAC, without using PulseAudio, if possible. gstout-audiodevice Set the audio device. After several hours, I'm asking for help. Audio options: ¶ -gstout-audiosink Set the audio sink. Way to generate a UUID is to create a UUID once by running the With this option, each renderer can be given its own id. Renderers running on the local network, they will all share the same reset () :Unblock writes and flush the device. bcm2835 ALSA Default Audio Device sysdefault:CARDALSA bcm2835 ALSA. prepare () :Configure the device with the specified format. Check what the sysdefault audio sink is that GMediaRenderer is going to use. This sets the UPNP UUID that is advertised and used byĬontrollers to distinguish different renderers. This is the most simple base class for audio sinks that only requires subclasses to implement a set of simple functions: open () :Open the device. u, -uuid UUID to advertise on the network in the form user:group. P, -pid-file Name of the file which the process ID should be written to. Libupnp does not use SO_REUSEADDR, so it might be This can only be a single address, and must be explicitly I, -ip-address The local IP address the service is running and advertised on. Audio options:-gstout-audiosink lt sinkgt Set the audio. One way to generate a UUID is to create a UUID once by running the uuidgen tool. If there are multiple renderers running on the local network, they will all share the same static ID. Usually, it is desirable for the renderer to show up onĬontrollers under a recognisable and unique name. Usually, gmediarender uses a built-in static id. f, -friendly-name Friendly name to advertise on the network. A summary of options is included below.Īpplication options: ¶ -d, -daemon Runs the program as a daemon. This program follows the usual GNU command line syntax, with long options Play media files from a UPNP-AV media server through an audio device on the It can be controlled from a UPNP-AV control point to Gmediarender is a daemon which acts as a UPNP-AV renderer This manual page documents briefly the gmediarender command. ![]() 前台运行 sudo -H -u gmrender bash -c "gmediarender -I ens3 -port=49152 -friendly-name=DOPLAY -gstout-initial-volume-db=0.SYNOPSIS ¶ gmediarender files. Methods inherited from class equals, getClass, hashCode, notify, notifyAll, toString. # END INIT INFO DESC = "gmRender" DAEMON_USER = "nobody:audio" UPNP_DEVICE_NAME = "Raspberry" INITIAL_VOLUME_DB =-10 declaration: package: processing.sound, class: AudioDevice. Sudo chown gmrender /var/log/gmediarender.logĬhmod +x /etc/init.d/gmediarender #!/bin/sh # BEGIN INIT INFO # Provides: gmediarender # Required-Start: $remote_fs $syslog $all # Required-Stop: $remote_fs $syslog # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Start GMediaRender at boot time # Description: Start GMediaRender at boot time. ![]() Sudo iptables -t filter -A INPUT -p udp -dest 239.255.255.250 -dport 1900 -j ACCEPT Sudo iptables -t filter -A INPUT -p tcp -dport 49152 -j ACCEPT Sudo apt-get install build-essential autoconf automake libtool pkg-config Sudo apt-get install libupnp-dev libgstreamer1.0-dev gstreamer1.0-plugins-base gstreamer1.0-plugins-good gstreamer1.0-plugins-bad gstreamer1.0-plugins-ugly gstreamer1.0-libav gstreamer1.0-alsa ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |